Are you currently in search of insight on A Step-by-Step Guide to Installing a Bathtub?
Mounting a bathtub isn't specifically rocket science, however it does call for solid plumbing, carpentry, and also sometimes, tiling skills. Changing an old bathtub with a new one is likewise a reasonably challenging job. If the old bathtub is readily easily accessible, the task can move rapidly; if you need to open up a wall to eliminate the old bathtub and also position the new tub, the job is a lot harder. In either instance, the project is within a home handyman's abilities, although you will certainly require a helper to move out the old bathtub and also embeded in the new one. Ensure you have actually certified on your own for the job and are comfortable trying it. As opposed to working with a contractor to take over a halfway-completed job, it is much better to take into consideration using one before you begin. Possibilities are you may require a specialist plumber to make tube links.
This write-up will help you install a new tub in your shower room if you have actually currently gotten a brand-new bathtub and also do not require to change the arrangement of your previous water supply pipes.
Your tools and material checklist ought to make up the following:
Removing Old Taps
If you need to replace old taps with new ones as a part of your installation, after that the first thing you need to do is separate the water. After doing so, activate the faucets to drain pipes any kind of water staying in the system. The procedure of eliminating the existing taps can be quite problematic due to the restricted accessibility that is usually the instance.
Make use of a container wrench (crowsfoot spanner) or a tap tool to undo the nut that attaches the supply pipelines to the faucets. Have a fabric ready for the remaining water that will originate from the pipelines. When the supply pipes have actually been eliminated, use the same device to loosen up the nut that holds the taps onto the bath/basin. You will require to quit the single taps from transforming throughout this process. Once the faucets have actually been eliminated, the holes in the bath/basin will need to be cleansed of any type of old sealing substance.
Prior to proceeding to fit the brand-new faucets, compare the pipe links on the old taps to the new faucets. If the old taps are longer than the new faucets, then a shank adapter is required for the brand-new taps to fit.
Fitting New Touches
If the tails of the new taps are plastic, after that you will require a plastic adapter to avoid damage to the string. One end of the connector fits on the plastic tail of the faucet as well as the other end gives a link to the existent supply pipelines.
If you need to fit a monobloc, then you will certainly require lowering couplers, which links the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next, place the faucet in the mounting opening in the bath/basin making certain that the washing machines are in location between the tap and also the sink. Secure the faucet in place with the supplier supplied backnut. Once the faucet is securely in position, the supply pipes can be linked to the tails of the taps. The faucets can either be connected by utilizing corrugated copper piping or with normal faucet connectors. The previous kind ought to be attached to the tap finishes first, tightening up only by hand. The supply pipelines can later be linked to the various other end. Tighten both ends with a spanner after both ends have been attached.
Setting up the Bath tub
Using the two wood boards under its feet, place the bath tub in the required setting. The wood boards are valuable in equally spreading the weight of the bath tub over the area of the boards rather than concentrating all the weight onto four small factors.
The following goal is to make sure that the bathtub is leveled all round. This can be accomplished by examining the spirit level as well as readjusting the feet on the bathtub up until the level reads level.
To set up faucets, fit the bottom of the outermost adaptable tap port to the ideal supply pipe by making a compression join; then do the exact same for the various other faucet.
Switch on the water system and also check all joints as well as brand-new pipework for leakages and tighten them if required. Fill up the bath tub and also check the overflow outlet as well as the regular electrical outlet for leaks.
Finally, repair the bathroom paneling as defined in the manufacturer's instruction manual. Tiling as well as securing around the bath tub needs to wait until the bathtub has been utilized at the very least when as this will certainly settle it into its final position.
Getting ready for the Setup
To start with, the sustaining structure supplied with the bath should be fitted (if required) according to the producer's directions. Next off, fit the faucets or mixer to the tub. When suitable the faucet block, it is necessary to see to it that if the faucet features a plastic washing machine, it is fitted in between the bathroom and also the faucets. On a plastic bathroom, it is additionally reasonable to fit a sustaining plate under the faucets device to stop pressure on the bath tub.
Fit the adaptable faucet adapters to the bottom of both faucets utilizing 2 nuts as well as olives (often provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the outlet via the hole in the bathroom. Make use of the nut provided by the maker to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the flexible overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bath. Make sure you make use of every one of the provided washers.
Connect the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a comparable manner.The bathroom ought to now prepare to be suited its final position.
Tiling Around the Bathtub
In the location where the bathroom meets the tile, it is essential to secure the joins with a silicone rubber caulking. This is important as the installation can move enough to fracture a stiff seal, triggering the water to penetrate the wall surface between the bath and also the tiling, causing complications with wetness as well as possible leakages to the ceiling below.
You can choose from a selection of coloured sealants to blend in your components as well as fittings. They are marketed in tubes as well as cartridges, and can sealing voids as much as a width of 3mm (1/8 inch). If you have a bigger gap to fill, you can load it with twists of drenched newspaper or soft rope. Keep in mind to always load the tub with water prior to sealing, to allow for the motion experienced when the tub remains in use. The sealer can crack rather early if you do not think about this motion prior to sealing.
Alternatively, ceramic coving or quadrant ceramic tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are additionally quickly readily available on the market. It is suggested to fit the tiles making use of water-resistant or water resistant glue as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We were brought to that write-up on Installing A Bathtub through an acquaintance on our other web property. Sharing is caring. You won't know, you might be helping someone out. Thanks for going through it.
Free Quote